固體絕緣材料絕緣電阻測試儀

符合標準：
GB/T 1410-2006《 固體絕緣材料體積電阻率和表面電阻率試驗方法》
ASTM D257-99《絕緣材料的直流電阻或電導試驗方法》
GB/T 10581-2006 《絕緣材料在高溫下電阻和電阻率的試驗方法》
GB/T 1692-2008 《硫化橡膠 絕緣電阻率的測定》
GB/T 2439-2001《硫化橡膠或熱塑性橡膠 導電性能和耗散性能電阻率的測定》
GB/T 12703.4-2010 《紡織品 靜電性能的評定 第４部分：電阻率》
GB/T 10064-2006_《測定固體絕緣材料絕緣電阻的試驗方法》
GB/T 22042-2008《服裝 防靜電性能 表面電阻率試驗方法》
EN 1149-1-1995 《防護服 靜電性能 第1部分表面電阻檢驗方法和要求》
GB/T 1410-2006《固體絕緣材料體積電阻率和表面電阻率試驗方法》（與標準IEC93-1980等效）
FZ/T 64013-2008 《靜電植絨毛絨》
SJ/10694-2006《電子產品制造與應用系統防靜電檢測通用規范》6.1 
一、概述
    本儀器既可測量高電阻，又可測微電流。采用了美國In公司的大規模集成電路,使儀器體積小、重量輕準確度高。數字液晶直接顯示電阻值和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍zui寬，準確度zui高的數字超高阻測量儀。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓10V/50V/100V/250V/500V/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便.     適用于橡膠、塑料、薄膜、地毯、織物及粉體、液體、及固體和膏體形狀的各種絕緣材料體積和表面電阻值的測定。
二、主要特點
電阻測量范圍寬 1×104Ω ～1×1018Ω
電流測量范圍為 2×10-4Ａ ～1×10-16Ａ
體積小、重量輕、準確度高
電阻、電流雙顯示
性能好穩定、讀數方便
所有測試電壓(10V/50V/100/250/500/1000V) 測試時電阻結果直讀，免去老式高阻計在不同測試電壓下或不同量程時要乘以系數等使用不便的麻煩，使測量超高電阻就如用萬用表測量普通電阻樣簡便。既能測超高電阻又能測微電流
三、技術指標
1、電阻測量范圍： 0.01×104Ω ～1×1018Ω。
2、電流測量范圍為： 2×10-4A～1×10-16A
3、顯 示 方 式：數字液晶顯示
4、內置測試電壓： 10V 、50V、100V、250、500、1000V
5、基本準確度：1% (*注)
6、使用環境： 溫度：0℃～40℃，相對濕度<80%
7、機內測試電壓： 10V/50V/100/250/500/1000V 任意切換
8、供電形式： AC 220V，50HZ，功耗約5W
9、儀器尺寸： 285ｍｍ× 245ｍｍ× 120 mm
10、質量： 約5KG
四、工作原理
    根據歐姆定律，被測電阻Rx等于施加電壓V除以通過的電流I。傳統的高阻計的工作原理是測量電壓V固定，通過測量流過取樣電阻的電流I來得到電阻值。從歐姆定律可以看出，由于電流I是與電阻成反比，而不是成正比，所以電阻的顯示值是非線性的，即電阻無窮大時，電流為零，即表頭的零位處是∞，其附近的刻度非常密，分辨率很低。整個刻度是非線性的。又由于測量不同的電阻時，其電壓V也會有些變化，所以普通的高阻計是精度差、分辨率低。
    本儀器是同時測出電阻兩端的電壓V和流過電阻的電流I，通過內部的大規模集成電路完成電壓除以電流的計算，然后把所得到的結果經過A/D轉換后以數字顯示出電阻值，即便是電阻兩端的電壓V和流過電阻的電流I是同時變化，其顯示的電阻值不象普通高阻計那樣因被測電壓V的變化或電流Ｉ的變而變，所以，即使測量電壓、被測量電阻、電源電壓等發生變化對其結果影響不大，其測量精度很高()，從理論上講其誤差可以做到零，而實際誤差可以做到千分之幾或萬分之幾。
典型應用
1、測量絕緣材料電阻(率)
2、測量防靜電材料的電阻及電阻率
3、測量計算機房用活動地板的系統電阻值
4、測量防靜電鞋、導電鞋的電阻值
5、光電二極管暗電流測量
6、物理,光學和材料研究
標準配置：
1、測試儀器：1臺
2、電源線：1條
3、測量線：3根（屏蔽線、測試接線、接地線）
4、使用說明書：1份
備注：
本儀器配不同的測量電極（夾具）可以測量不同材料（固體、粉體或液體）的體積電阻率和表面電阻率或電導率，*符合國家標準GB1410－2006固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法，ASTM D257 絕緣材料的直流電阻或電導試驗方法 等標準要求。
注意事項：
儀器使用前請仔細閱讀以下內容，否則將造成儀器損壞或電擊情況。
1. ★檢查儀器后面板電壓量程是否置于10V檔，電流電阻量程是否置于104檔。
2. ★接通電源調零，（注意此時主機不得與屏蔽箱線路連接）在“Rx"兩端開路的情況下，調零使電流表的顯示為0000。然后關機。
3. ★將待測試樣平鋪在不保護電極正中央，然后用保護電極壓住樣品，再插入被保護電極（不保護電極、保護電極、被保護電極應同軸且確認電極之間無短路）。
4. ★測體積電阻時測試按鈕撥到Rv邊，測表面電阻時測試按鈕撥到Rs邊，
5. ★接好測試線，將測試線將主機與屏蔽箱連接好。量程置于104檔，打開主機后面板電源開關按鈕。從儀器后面板調電壓按鈕到所要求的測量電壓。
(比如：GBT 1692-2008 硫化橡膠 絕緣電阻率的測定 標準中注明要求在500V電壓進行測定，那么電壓就要升到500V)
6. ★電流電阻量程按鈕從低檔位逐漸撥高檔，每撥一次停留1-2秒觀察顯示數字，當被測電阻大于儀器測量量程時，電阻表顯示“1"，此時應繼續將儀器撥到量程更高的位置。
測量儀器有顯示值時應停下，在1min的電化時間后測量電阻，當前的數字乘以檔次即是被測電阻。
7. ★測試完畢先將量程撥至（104）檔，然后將測量電壓撥至10V檔，zui后將測試按鈕撥到中央位置后關閉電源。然后進行下一次測試。
8. ★應在“Rx"兩端開路時調零，一般一次調零后在測試過程中不需再調零。
9. ★禁止將“RX"兩端短路，以免微電流放大器受大電流沖擊。
10. ★不得在測試過程中不要隨意改動測量電壓。
11. ★測量時從低次檔逐漸撥往高次檔。
12. ★接通電源后，手指不能觸及高壓線的金屬部分。
13. ★不得測試過程中不能觸摸微電流測試端。
14. ★在測量高阻時，應采用屏蔽盒將被測物體屏蔽。
15. ★嚴禁在試測過程隨意改變電壓量程及在通電過程中打開主機。
16. ★嚴禁電流電阻量程未在104檔及電壓在10V檔，更換試樣。

Meet the standard:

GB/T 1410-2006《 固體絕緣材料體積電阻率和表面電阻率試驗方法》

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method"

ASTM D257-99《絕緣材料的直流電阻或電導試驗方法》

DC resistance or conductance of insulating materials test method "ASTM D257-99"

GB/T 10581-2006 《絕緣材料在高溫下電阻和電阻率的試驗方法》

Test method GB/T 10581-2006 "insulation resistance at high temperature and resistivity"

GB/T 1692-2008 《硫化橡膠 絕緣電阻率的測定》

Determination of 1692-2008 vulcanized rubber insulation resistivity of "GB/T"

GB/T 2439-2001《硫化橡膠或熱塑性橡膠 導電性能和耗散性能電阻率的測定》

GB/T 2439-2001 "rubber vulcanized or thermoplastic conductive properties and dissipative properties determination of resistivity"

GB/T 12703.4-2010 《紡織品 靜電性能的評定 第４部分：電阻率》

GB/T 12703.4-2010 "textile xerographic performance evaluation of fourth parts: the resistivity"

GB/T 10064-2006_《測定固體絕緣材料絕緣電阻的試驗方法》

GB/T 10064-2006_ "determination of solid insulation resistance of insulation materials test method"

GB/T 22042-2008《服裝 防靜電性能 表面電阻率試驗方法》

GB/T 22042-2008 "garment test methods for the prevention of electrostatic properties of surface resistivity"

EN 1149-1-1995 《防護服 靜電性能 第1部分表面電阻檢驗方法和要求》

EN 1149-1-1995 "protective clothing electrostatic properties of first part surface resistance test methods and requirements"

GB/T 1410-2006《固體絕緣材料體積電阻率和表面電阻率試驗方法》（與標準IEC93-1980等效）

GB/T 1410-2006 "solid insulating material volume resistivity and surface resistivity test method" (international standard IEC93-1980 equivalent)

FZ/T 64013-2008 《靜電植絨毛絨》

FZ/T 64013-2008 "electrostatic flocking Plush"

SJ/10694-2006《電子產品制造與應用系統防靜電檢測通用規范》6.1

SJ/10694-2006 "electronic product manufacturing and application of anti electrostatic detection system general specification" 6.1

一、概述

One, overview

本儀器既可測量高電阻，又可測微電流。采用了美國In公司的大規模集成電路,使儀器體積小、重量輕準確度高。數字液晶直接顯示電阻值和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍zui寬，準確度zui高的數字超高阻測量儀。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓10V/50V/100V/250V/500V/1000V任意可調。本儀器具有精度高、顯示迅速、性好穩定、讀數方便. 適用于橡膠、塑料、薄膜、地毯、織物及粉體、液體、及固體和膏體形狀的各種絕緣材料體積和表面電阻值的測定。

This instrument can measure high resistance, but also can measure current. Use of large scale integrated circuit American company In, the instrument has the advantages of small volume, light weight and high accuracy. Digital LCD display resistance value and the current. Range from 1 × 104 Ω to 1 × 1018 Ω, is currently the most wide measuring range, accuracy the highest high resistance measuring instrument. Current measuring range is 2 × 10-4 ～ 1 × 10-16A. The built-in test voltage 10V/50V/100V/250V/500V/1000V adjustable. The instrument has high precision, good stability, shows a rapid, convenient reading. Suitable for rubber, plastics, film, carpets, fabrics and powder, liquid, and solid and pasty shape insulating materials by volume and surface resistance value.

二、主要特點

Two, the main features

電阻測量范圍寬 1×104Ω ～1×1018Ω

Resistance measurement range of 1 × 104 to 1 × 1018 Ω

電流測量范圍為 2×10-4Ａ ～1×10-16Ａ

Current measuring range is 2 × 10-4A ～ 1 × 10-16A

體積小、重量輕、準確度高

Small volume, light weight, high accuracy

電阻、電流雙顯示

Resistance, current double display

性能好穩定、讀數方便

Good performance is stable, easy reading

所有測試電壓(10V/50V/100/250/500/1000V) 測試時電阻結果直讀，免去老式高阻計在不同測試電壓下或不同量程時要乘以系數等使用不便的麻煩，使測量超高電阻就如用萬用表測量普通電阻樣簡便。既能測超高電阻又能測微電流

All voltage test (10V/50V/100/250/500/1000V) resistance results test reading, from old high resistance meter in different test voltage or different range should be multiplied by the coefficient of inconvenience and trouble, ultra high resistance as measured with a multimeter common resistance is measured. Not only can measure high resistance and micro current

三、技術指標

Three, technical indicators

1、電阻測量范圍： 0.01×104Ω ～1×1018Ω。

1, resistance measurement range: 0.01 × 104 ~ 1 × 1018 Ω.

2、電流測量范圍為： 2×10-4A～1×10-16A

2, the current measurement range: 2 × 10-4A ～ 1 × 10-16A

3、顯 示 方 式：數字液晶顯示

3, the display mode: Digital LCD display

4、內置測試電壓： 10V 、50V、100V、250、500、1000V

4, the built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V

5、基本準確度：1% (*注)

5, basic accuracy: 1% (note)

6、使用環境： 溫度：0℃～40℃，相對濕度<80%

6, the use of the environment: temperature: 0 ℃ ~ 40 ℃, relative humidity <80%

7、機內測試電壓： 10V/50V/100/250/500/1000V 任意切換

7, the built-in test voltage: 10V/50V/100/250/500/1000V arbitrary switching

8、供電形式： AC 220V，50HZ，功耗約5W

8, the power supply form: AC 220V, 50HZ, power consumption is about 5W

9、儀器尺寸： 285ｍｍ× 245ｍｍ× 120 mm

9, the instrument size: 285mm x 245mm x 120 mm

10、質量： 約5KG

10, quality: about 5KG

四、工作原理

Four, work principle

根據歐姆定律，被測電阻Rx等于施加電壓V除以通過的電流I。傳統的高阻計的工作原理是測量電壓V固定，通過測量流過取樣電阻的電流I來得到電阻值。從歐姆定律可以看出，由于電流I是與電阻成反比，而不是成正比，所以電阻的顯示值是非線性的，即電阻無窮大時，電流為零，即表頭的零位處是∞，其附近的刻度非常密，分辨率很低。整個刻度是非線性的。又由于測量不同的電阻時，其電壓V也會有些變化，所以普通的高阻計是精度差、分辨率低。

According to Ohm's law, the measured resistance Rx is equal to the applied voltage divided by current V by I. The working principle of high resistance meter is the traditional measure voltage V fixed, by measuring the current flows through the sampling resistor I to get the resistance value. From Ohm's law can be seen, the current I is inversely proportional to the resistance, not proportional, so is nonlinear resistive display value, namely the infinite resistance, current is zero, i.e. zero at the header is ∞, graduated in the vicinity of the very tight, very low resolution. The scale is nonlinear. Because the resistance measurement is different, its voltage V there will be some changes, so the high resistance of ordinary meter is poor accuracy, low resolution.

本儀器是同時測出電阻兩端的電壓V和流過電阻的電流I，通過內部的大規模集成電路完成電壓除以電流的計算，然后把所得到的結果經過A/D轉換后以數字顯示出電阻值，即便是電阻兩端的電壓V和流過電阻的電流I是同時變化，其顯示的電阻值不象普通高阻計那樣因被測電壓V的變化或電流Ｉ的變而變，所以，即使測量電壓、被測量電阻、電源電壓等發生變化對其結果影響不大，其測量精度很高()，從理論上講其誤差可以做到零，而實際誤差可以做到千分之幾或萬分之幾。

This instrument is current and voltage V and flow resistance at the same time measuring resistor I, the large scale integrated circuit internal to complete the calculation of voltage divided by current, and then the obtained results after A/D conversion to digital display resistance value, even if is current and voltage of V and flow resistance at both ends of the I is changed at the same time, the displayed value resistance do not like ordinary high resistance meter for V measured voltage or current change of I variable and variable, so, even if the measurement of voltage, resistance, power supply voltage is measured and the change had little effect on the results, the measuring accuracy is very high (patent), theoretically the error can be do zero, while the actual error can be done a few thousandths or very few.

典型應用

Typical applications

1、測量絕緣材料電阻(率)

Insulation resistance 1, measurement (rate)

2、測量防靜電材料的電阻及電阻率

2, the measurement of anti resistance and resistivity electrostatic materials

3、測量計算機房用活動地板的系統電阻值

3, the measurement used in computer room floor system resistance value

4、測量防靜電鞋、導電鞋的電阻值

Resistance of 4, measurement of anti-static shoes, conductive shoes value

5、光電二極管暗電流測量

5, photoelectric diode dark current measurement

6、物理,光學和材料研究

6, physical, optical and material research

標準配置：

Standard configuration:

1、測試儀器：1臺

1, test equipment: 1 sets

2、電源線：1條

2, power line: 1

3、測量線：3根（屏蔽線、測試接線、接地線）

3, the measuring line: 3 (shielding line, test line, ground wire)

4、使用說明書：1份

4, use instructions: 1

備注：

Remarks.

本儀器配不同的測量電極（夾具）可以測量不同材料（固體、粉體或液體）的體積電阻率和表面電阻率或電導率，*符合國家標準GB1410－2006固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法，ASTM D257 絕緣材料的直流電阻或電導試驗方法 等標準要求。

This instrument measuring electrode with different (fixture) can measure different materials (solid, powder or liquid) of the volume resistivity and surface resistivity or conductivity, fully meet the national standard GB1410 - 2006 solid electrical insulation resistance, volume resistivity and surface resistance test method of material, ASTM D257 DC resistance or conductance of insulating materials test method standard.

注意事項：

Matters needing attention:

儀器使用前請仔細閱讀以下內容，否則將造成儀器損壞或電擊情況。

The instrument before use, please read the following carefully, otherwise it will cause equipment damage or shock condition.

1. ★檢查儀器后面板電壓量程是否置于10V檔，電流電阻量程是否置于104檔。

1. Check the instrument panel after voltage range is placed in the 10V file, current resistance range is placed 104.

2. ★接通電源調零，（注意此時主機不得與屏蔽箱線路連接）在“Rx"兩端開路的情況下，調零使電流表

2 ★ power zero, (note that the host may not be connected with the shielding box line) in the "Rx" both ends open circuit case, zero current meter

The electrical properties of China aerotime and common instrument of insulating material

ZWN萬能材料試驗機

ZWN universal material testing machine

ZJC-10KV-200KV電壓擊穿試驗儀

ZJC-10KV-200KV voltage breakdown tester

ZST-121體積表面電阻率測定儀

Determination of ZST-121 volume and surface resistivity instrument

ZTS-121碳素材料電阻率測試儀

ZTS-121 carbon material resistivity tester

ZST-122電線電纜導體半導體材料電阻率測試儀

Instrument cable conductor semiconductor material resistivity ZST-122

M-200橡膠塑料滑動摩擦試驗機（國標，非國標，可定制）

M-200 rubber plastic sliding friction testing machine (GB, non standard, can be customized)

ZJD-A介電常數介質損耗測試儀（可測試固體液體）

ZJD-A dielectric loss tester (testing of solid liquid)

ZJD-B學校介電常數介質損耗測試儀

ZJD-B school special dielectric loss tester

ZJD-C高頻介電常數介質損耗測試儀

ZJD-C high frequency dielectric loss tester

ZJD-50HZ-100HZ工頻介電常數介質損耗測試儀

ZJD-50HZ-100HZ frequency dielectric loss tester

ZDH-20KV絕緣材料耐電弧性能試驗儀/高電壓小電流測試儀

Arc resistance tester / high voltage low current tester ZDH-20KV insulating material

ZWK-300A液顯熱變形維卡軟化點溫度測定儀

ZWK-300A liquid heat deformation temperature of VEKA softening point tester

ZWK-300B計算機控制熱變形維卡溫度試驗機

VEKA ZWK-300B computer control thermal deformation temperature testing machine

ZWK-500計算機控制熱變形維卡溫度試驗機

VEKA ZWK-500 computer control thermal deformation temperature testing machine

ZQYH-96塑料球壓痕硬度計

ZQYH-96 plastic ball indentation hardness tester

ZRT-400Z熔體流動速率測定儀/熔融指數儀

ZRT-400Z melt flow rate meter / melt index apparatus

ZMD-A計算機控制馬丁耐熱試驗儀

ZMD-A computer control Martin heat resistance tester

☆中航時代燃燒性能儀器

☆ China aerotime combustion performance instrument

ZRS-3水平垂直燃燒試驗儀

ZRS-3 horizontal and vertical burning tester

ZDG-1000單根電線電纜垂直燃燒試驗儀

ZDG-1000 vertical burning test instrument of single wire and cable

ZLD-600V漏電起痕試驗儀

ZLD-600V tracking test apparatus

ZLD-6000V高壓漏電起痕試驗儀

ZLD-6000V high voltage tracking test apparatus

ZKR-A建材可燃性試驗爐

ZKR-A building materials flammability test furnace

ZBR-B建材不燃性試驗爐

ZBR-B building materials not combustion test furnace

ZZR-A汽車內飾材料阻燃性能試驗機

Flame retardant properties of automotive interior materials testing machine ZZR-A

ZY-A針焰試驗儀

ZY-A needle flame test apparatus

ZR-A灼熱絲試驗儀

ZR-A glow wire test apparatus

ZDR-C導熱系數測定儀

Determination of ZDR-C thermal conductivity coefficient instrument

☆中航時代海綿泡沫檢測儀器

☆ China aerotime sponge foam detecting instrument

ZYX-2000海綿泡沫壓陷硬度測定儀

ZYX-2000 sponge foam indentation hardness tester

ZLQ-500海綿泡沫落球回彈儀

ZLQ-500 sponge foam ball rebound tester

ZPL-2000海綿泡沫疲勞沖擊測定儀

ZPL-2000 sponge foam fatigue impact tester

ZLS-1000海綿拉伸強度試驗機

ZLS-1000 sponge tensile strength testing machine

ZYS-200海綿壓縮*變形試驗機

Compression testing machine ZYS-200 sponge

ZQG-500海綿泡沫切割機

ZQG-500 sponge foam cutting machine

ZMD-A海綿密度測定儀

ZMD-A sponge density measuring instrument

ZYZS-C氧指數測定儀

ZYZS-C oxygen index tester

ZR-B海綿泡沫阻燃性能試驗箱

Test box flame retardant sponge foam properties of ZR-B

☆中航時代沖擊試驗機系類

☆ China aerotime impact testing machine series

ZWD系類低溫脆性試驗機（單試樣、多試樣）

ZWD series of brittle - temperature testing machine (single specimen, multiple sample)

ZJZL-A簡支梁沖擊試驗機（指針，數顯）

ZJZL-A Charpy impact testing machine (pointer, digital display)

ZXBL-A懸臂梁沖擊試驗機（指針，數顯）

ZXBL-A cantilever beam impact testing machine (pointer, digital display)

ZJX-A簡支梁懸臂梁組合沖擊試驗機（指針，數顯）

ZJX-A simply supported cantilever beam combination impact testing machine (pointer, digital display)

ZLC-2000落球沖擊試驗機

ZLC-2000 falling ball impact test machine

ZLB-30管材落鏢沖擊試驗機

ZLB-30 pipe falling dart impact tester

BCM-03擺錘薄膜沖擊試驗機

Pendulum impact testing machine of BCM-03 thin films

ZJS-300A金屬擺錘沖擊試驗機

ZJS-300A metal pendulum impact testing machine

ZJS-300B全自動低溫沖擊試驗機

ZJS-300B automatic temperature impact test machine

☆中航時代制樣機系類

☆ China aerotime system prototype system

ZWN-A萬能制樣機

The ZWN-A universal machine

ZQK-A手動缺口制樣機

ZQK-A manual gap system prototype

ZQK-B自動缺口制樣機

ZQK-B automatic gap system prototype

ZYL-A手動啞鈴型制樣機

ZYL-A manual dumbbell system prototype

ZQK-B自動啞鈴型制樣機

ZQK-B automatic dumbbell system prototype

沖片機（氣動、液壓）

Punching machine (pneumatic, hydraulic)

☆中航時代環境試驗箱系類

☆ China aerotime environmental test box series

ZJB-C高低溫交變試驗箱

ZJB-C alternating high and low temperature test box

ZQH-C人工氣候箱

ZQH-C artificial climate box

ZLH-A老化試驗箱

ZLH-A aging test box

ZWS-02高低溫試驗箱

ZWS-02 high low temperature test box

ZYZS-C氧指數測定儀

ZYZS-C oxygen index tester

☆售后服務

☆ after sale service

一、安裝調試：協助試驗機的安裝，負責試驗機的運輸、調試。

A, installation debugging: assist testing machine installation, transportation, commissioning test machine.

二、驗收標準：試驗機按訂貨技術附件進行驗收。終驗收在買方進行，對用戶提供的試樣進行試驗，并提供測試報告。

Two, acceptance criteria: testing machine for acceptance according to the order of the technical annex. Final acceptance in the buyer, sample provides to the user testing, and provide the test report.

三、培訓：安裝調試同時，在儀器操作現場一次性免費培訓操作人員2-3名，該操作人員應是由需方選派的長期穩定的員工，培訓后能夠?qū)υO(shè)備基本原理、軟件使用、操作、維護事項理解和應用，使人員能夠獨立操作設備對樣品進行檢測、分析，同時能進行基本的維護。

Three, training: installation at the same time, the instrument operation on-site one-time free training 2-3, the operating personnel shall be appointed by the long-term stability of the staff, training to basic principle, software use, operation, maintenance and application of understanding, so that workers can operate independently equipment to detect samples, analysis, at the same time can carry out basic maintenance.

四、軟件升級：終生免費提供新版本控制軟件。

Four, software upgrade: free lifetime provides new version control software.

五、保修：

Five, the warranty:

1、設備保修兩年，終身售后服務，一年內非人為損壞的零部件免費更換，保修期內接到用戶邀請后， zui遲響應時間為2小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法 。

1, equipment warranty of two years, lifetime after sale service, within one year of the non-human damage parts replaced free of charge, the warranty period the user received the invitation, but the response time is 2 hours, with user confirmation after a failure, I will send engineers arrived at the scene for free within 48 hours of service, find out the fault location and the fault reason as soon as possible, and to users timely report failures and troubleshooting.

2、保修期內人為損壞的零部件按采購（加工）價格收費更換。

2, the warranty period of man-made damaged parts procurement according to the price of replacement (processing).

3、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后3天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。

3, the warranty period to continue to provide high-quality technical services for the users, to invite users to repair within 3 days after the arrival of the user site to send engineers to repair. And enjoy the preferential purchase of spare parts.

4、傳感器過載及整機電路超壓損壞不在保修范圍內。

4, the sensor and the circuit overload overpressure damage not covered under warranty.

六、售后管理：

Six, customer service management:

我公司實現計算機化管理，實行客戶定期回訪制度，定期復查設備的工作情況，定期指導用戶對設備進行保養和檢測，以便設備正常運轉，跟蹤客戶的設備使用情況，以便及時對設備進行維護。

Our company to realize the computer management, carry out customer regular ephone return visit system, work regular examination equipment, regular ephone guide users to maintain and test the equipment, so that the normal operation of equipment, track customer equipment usage, so that timely equipment for maintenance.